Category

Mountaineering Equipment

Ice climbing in Valdres – Beitostølen / Kalvedalen

By | Ice axes, Ice axes, Ice axes, Ice climbing in Valdres, Mountaineering Equipment, Petzl, Uncategorized | No Comments

Date: 04.12.2018

Winter is a special time, it’s always changing. Today it was changing by the minute.

On a recon tour to Kalvedalen, which is found off Beito (Down from Beitostølen). A semi-hidden valley that contains a few steep ice falls.

My companion today: Tinde our Alaskan malamute. In winter she is the master, the way she holds herself in winter is just to watch and learn. Following the small river into hidden valley she moves warily over the frozen stream, aware of the water below. She is such at peace with herself in this environment, right there in nature. Its a reminder to myself how often I am not present to the tour, and often inside my own head. Thinking away and not being present. She walks, her body language changes, suddenly she moves to one side, sniffs the snow. I continue, and suddenly! I’m through the snow and ice into the stream below. Luckily today I had on my wellies 😉 Tinde never goes through.

Ice Climbing in Valdres – Trillefossen

By | DMM, Ice axes, Ice axes, Ice axes, Ice axes, Ice climbing in Valdres, Mountaineering skills, Petzl, Winter | No Comments

Date: 01.12.2018

The joys of winter 😏 After a cold spell I suddenly remembered a fall very close to home. Martin and I set off full of hope, however at the parking place I could see it had fallen down 😂. On a recon tour two days before it had looked good. We walked in anyway and climbed a short pitch of good ice to the left. Fun in a early season, first winter route, haven’t done this in awhile sort of scary, this is steeper that expected way. It would seem becoming a dad hasn’t miraculously made me into a super dad climber. Back to the gym 😊

Nice walk in the forest. Very special. Tinde enjoyed herself. Went quite puppy crazy when we abbed backdown to her.

I’ll be back…. as the terminator would say… for the main event.

 

Crevase Rescue or buddy rescue systems

By | Alpine Rescue, Crevasse rescue, Mountaineering Equipment, Mountaineering skills | No Comments

Personally, I think the system you use to haul your buddy out of a hole in a glacier should be the same as you would use to haul them up in any situation. Why? You learn one system, learn it really well, so its second nature and then you will have it nailed for that time you really need it.

This series follows on from the blog post about “What crevasse equipment”

In reality, we seldom need to use these rescue system, in most cases with good rope work we can reverse and drag our buddy out of the crevasse before they take a big drop or if they do go in they extract themselves by prusiking back out.  To haul a person up a pitch or crevasse is going to take a lot of energy and time, think carefully before hauling as there might be an easier alternative. The only group that regularly use these systems are instructors and guides to help participants overcome crux moves.

The basic system regardless of equipment is a 3:1 pulley. This system works, but boy will you have to work and if your a bit of a wimp or your buddy has eaten too many pies you’re going to have to think about getting some gadgets or some tricks to help you along the way.

The basic 3: 1 pulley often referred to as a Z system is a working solution and if you’re using basic equipment, just the rope, carabiners and prusiks this system will have a good ratio of effect versus friction. If you try to build it out more, then the friction will exponentially increase and undo all your good pulling effort. To build out effectively you need pullies in the system to reduce friction.

Regardless of the terrain, be it a glacier, cornice, a hole in the snow or steep rock the system is the same, it’s only the belays that changes. On rock, you can build rock belays and on snow, you need to use snow anchors or if lucky find some ice to build an ice screw belay.

Essentially you need an anchor, an anchor that is solid and will not fail and then you build you 3:1 system to it. And then pull like crazy 🙂

The anchor is a howl subject and fieldwork experience in itself. On courses I run, we use a lot of time building different snow anchors, testing them, finding each anchors advantage and disadvantage, seeing there weaknesses and strengths. Placing a snow anchor is never going to be perfect, it will always be a compromise. In wet summer snow, you can get away with less precisely placed anchors, while the same set up in dry winter snow wouldn’t work all. It doesn’t matter how well placed the snow anchor is, the snow will always fail at some point. In most cases, maybe in all, if the anchor fails it fails catastrophically without warning.

 

Picture 2: Crevasse rescue: 3 to 1 – Z pulley system

Back to the simple 3:1 set up. Gadgets aside we are just using basic equipment:
2 x prusiks
2 x carabiners (At least one, in theory, should be a screw gate)
1 x rope

Obviously, we could swop things out, as this is “improvised rescue”. Instead of prusiks, we could use slings, preferable nylon as they grip better, but skinny spectra can also grip as well. If we don’t have screw gate carabiner we could use two open gates, with the gates opposite each other.

In Picture 2, Antonia has set up a 3:1 system attached to a deadman snow anchor. Ideally, she would be pulling the rope more in the direction of the anchor and inline with the rope running to her partner James, pulling in any other way reduces the effectiveness of the system.

1 = Carabiner (hopefully a screw gate) attached to the snow anchor. 2 = Prusik (ideally a knot called a “french”). 3 =Prusik (ideally a knot called “Klemheist knot” or called a “Viking” in Norway). 4 = open carabiner. 5 = Snow anchor (in this case a “deadman”)

This simple system is the basic starting block of any pulley system.  The problem with this system is friction. It is a rather inefficient system because of friction and to haul your buddy out will take quite a lot of muscle power. In this case, Antonia will also have to pull up the hill. If she was able to attach another carabiner to the anchor she would be able to use the downhill to help her, although friction would increase in the system. Regardless of her best efforts, her partner James weighted over 100kg and it was not possible to haul him out of the crevasse. She would need another system which will be discussed later.

Picture 2: 3 to 1 pulley system

 

 

 

In Picture 2, we see a similar system using a micro-traction (1)(a pulley wheel with a grip so the rope can spin free in one direction but can’t in the other), a pulley wheel (2) and a metal prusik (Tibloc) (3). All this is in this case attached to a bolt belay (4).

 

Using these gadgets (pulley wheels and mechanical grips) reduces the friction markedly over our basic rope and carabiner set up.  Here Alex drags me up a steep rock route but again he is pulling in an uphill direction and going against gravity. If he was able to attach another pulley wheel to the anchor he could start pulling down and use his muscle, body weight with gravity to help haul me up.

The problem with this system is you need some gadgets that weight a bit and most alpine climber are looking to go light and don’t need any extra grams. They also have a defined goal and can’t be used in other situation. Your basic prusiks can be used to climb a rope, abseil cord, or even tieing your shoes and loads more.

Discussion:

Even against your best muscle efforts it just might be impossible to haul your buddy up. In the case of crevasses, if the snow is overhanging and you buddy is free-hanging there is a chance the rope will cut the snow and when you pull him up he will jam under the overhanging snow, similarly if you haul your buddy up and he gets caught in a chimney or overhand it might be impossible to haul him. So in theory, they work, in practice, you might get caught up in a natural trap.

Test your gear!  Nice shinny ropes with nice shinny prusiks don’t always grip together as well as you would like.  Best to try your system at home to see it all works out before you need it in anger. The diameter of the prusiks should be less than the diameter of the rope your going to climb.

Getting extra help – building out the haul system:

It is possible to add in an extra sling or rope in this system to form a 5:1 or what is often more accurately described as a 3 + 2:1 system.  In this case, a 120cm nylon sling is being used to form the extra built out section of the pulley (The 2 in the 3+2:1 system). It would be possible to use cord, for example, your abseil cord.  Using a 120cm sling reduces the distance you can pull (60cm), and you’re also pulling away from your buddy which might not be helpful if you’re on a slope or have another crevasse nearby.  All cute problems.  They just keep coming!

Picture 4: 3 +2 :1 pulley system,

Knots (hindering knots) on the rope)

It is not uncommon to tie hindering knots on the rope, especially if there are only two people on that rope.  How useful they are in actually hindering a full fall is dependent on the amount of snow and the snow quality overlaying the actual glacier or for that matter hard layers like ice. The snow has to be deep enough and the right consistency to grip the knot.  If the snow is to thin the ropes and knots cut through the snow to the glacier and don’t bit, on the other hand, if the snow is deep enough the hindering knots have a tendency to jam in the snow and reduce the force on you considerable.

It is better explained here: Hindering knots 

 

The participant hops over the hindering knot with prusik and has started to attach the 120cm sling. The participant has disconnected the rope from the second prusik. This isn’t necessary however it does make it easier to see whats what when setting up.

Hindering knots adds a cute problem in rescue.  They don’t go thought carabiners or prusiks. At all.  In many mini-movies about crevasse rescue, this is often skipped over. In some cases, a knotted rope suddenly is un-knotted without explanation. It’s not possible to untie a hindering knot when the rope is loaded. The only way to do this is by releasing the load and then untieing it.

The way this is done while in a rescue situation is to pull the rope up until the hindering knot is approximately 1m from the belay carabiner. Make sure the prusik (It’s going to have to be a “french” for the next stage) bites and takes the weight of your buddy. Leap your second prusik over the hindering knot and attach a 120cm sling that is attached to the belay to the second prusik (often a klemheist). Slide this prusik as far forward as possible so it is tight with the belay. Now slowly and surely message the french prusik at the belay so the rope glides out (under control) and is taken fully on the second prusik. You are now able to slacken the main rope and untie the hindering knot.  Don’t expect it to be easy, the knot has been under force. Once the knot is untied you can make the main rope tight to the first prusik and attach the rope to the second prusik to form 3:1 pulley again and start lifting your buddy a little to remove the 120cm sling. Obviously, you can use a different sling length.

If you are unable to untie the hindering for whatever reason (its jammed solid or frozen) then some more jiggery-pokery is required. Hop over the knot with the second prusik as described above. When the hindering knot comes close to the belay carabiner tie a new french prusik below the knot and massage the first french prusik so the rope glides and is taken up by the other prusik. Once this is complete you can untie the first prusik.  It will almost certainly require you to extend the belay carabiner slightly so the hindering knot is on the right side of the belay carabiner. You could use a short sling. Once this is complete you can continue to pull. Phew! lets hope you can untie the hindering knot!

Discussion:

Hindering knots do help in the right snow conditions, however they can be a pain as well. If suddenly you pass thought some ice and need to use some ice screw running belays you are going to have to undo all the knots. Likewise if you transfer from snowy glacier to land and need to protect those glacially smooth slabs before you get to a good belay you can’t until those hindering knots are removed. An alternative is described below.

Having the right knot at the belay carabiner is important. The  “French” knot has the advantage that under load you can message it and the rope can glide out. The disadvantage of this knot is the very thing we like about it, this ability to slip the main rope when messaged. If you knock this knot by accident it can start to loosen its grip on the main rope just at the point you would rather it would not. Klemhiest knots are very good at gripping the rope but are almost impossible to release when under load.

Two man rope team (Alpine Climbers)

Alternatively, you could use two ropes which is common practice for alpine climbers. The two-person climbing rope team comprises two ropes (nominally 60m long / 8mm diameter – Think half ropes), standard alpine crevasses rescue system (2 x prusiks, 2 x crabs).  You and your buddy tie in at the ends as normal and take coils for 20m, so you and your buddy are 20m apart. One rope is clean (no knots) and forms the rescue rope (the one you’re going to drag your mate up with) and the other is you hindering rope and contains hindering knots like alpine butterflies every 2m or so. These knots hinders the fall as they become jammed in the snow and are very effective in the right type of snow.  Obviously, it has to be a snow-covered glacier and depth of snow is also critical. Another obvious fact is the clean rope will require more coils than the hindering rope.

The following picture (picture 5) is of a two-person climbing team system, which is often used in Norway.  I have, probably like many others modified it and not strictly followed the Norwegian standard (The modification is the Norwegians don’t tie into the ends but come in 20m and tie-in with a huge overhand knot – I tried to find out why they did this but never got a good answer. I think it has to do with this is the way they do it if they are 3 to 4 people on a rope with the ends of the rope being used as the rescue line –  See description later).

Picture 5: Two-person climbing rope team. Clean rescue rope on the left and hindering rope with knots on the right. In this case, we used 1 x 60m combi rope (Goes as single or a double at 8.9mm)  doubled up. The photo was taken on Falktind glacier early summer 2018.

 

Picture 6 shows a demonstration of the rescue set up with this two rope system.

 

Picture 6: Rescue set up with the two people climbing team.

Number 1 = The hindering rope (yellowy rope), which would be attached as quickly as possible to the first section of the anchor after a fall (number 2 – klemheist knot on an ice screw).  In this case, all prusiks where set up on the rope before rescue which is a standard form in Norway. Getting the load from you onto to the first ice screw makes everything so much easier. One your buddy’s weight is on the first ice screw you can set up the belay with another equalised ice screw, or a snow anchor and/or buried axe. In this picture, the guy with the white helmet on the left has set up the belay and started to form the 3:1 system with a klemheist knot (Number 3) and a “french knot” numbered 4 in the picture.  As you can see there are loads of rope laying around and this is not uncommon. It can get messy with two ropes and there can be massive amounts of rope mess unless your well organised.

 

Discussion:

In this situation your first prussic (number 2) can form your back-up to the main haul system. Obviously there is a lot of rope about and organisation is key.

 

 

 

 

 

 

 

 

 

Picture 7 Snow anchor and ice ax belay

In picture 7, the participants have placed both a snow anchor (deadman) and ice axe to form a solid belay.

This is a standard Norwegian method. It might seem overkill in wet summer snow, however, it is good practice as a climber with climbing axes might need to bury both to get a good enough belay.

In this case, the snow anchor is placed first. Then the anchor is clipped into the ready-made prusik. When transferring the weight from your body onto the anchor its is important to do this gradually and in control with your eyes darting back and forth from the prusik and snow anchor to see both are holding. In the case of the prusik if it doesn’t grip it will normally need dressing properly or wrapping around the rope some more, while the snow anchor will normally fail catastrophically without warning, and it is, therefore, important to be ready for this eventuality as failure of the belay will transfer all the weight of your buddy back to you. Be prepared! Be ready!

Obviously, if you have never built an ice axe belay while laying face down in the snow with your buddies weights trying to pull you down the same crevasse he has fallen then its worth trying with a safety back up a belay and a few friends around to help out if everything goes crazy 🙂 Its a real eyeopener.

 

 

 

 

The following picture series shows Alex using a two-person climbers team set up after a person has fallen into a crevasse. In this case, I set up a pulley to form the fallen climber. He is using a single axe as the snow anchor.

Crevasse rescue – Alex makes an axe belay. I used a back pulley to form the weight of the fallen climber as there was only two us.

 

Burying the axe. Alex has buried his axe with snow to make absolutely sure its bomb proof. Still, face down! Still bearing all the load on his legs, harness and hips!

 

Clipping the anchor into the prusik…. Or trying to…. In this case, a small mistake when setting up, in the beginning, resulted in Alex having to tie a new prusik. Cute problems happen in improvised rescue. Solution? Improvise. In this case, the screw gate carabiner, which was being used to fix and direct the coiled rope had turned to face the body, entangling the rope and prusik into a nice mess. Not easy to undo when holding the weight of your buddy face down in the snow.

Phew! Clipped into the belay at last. Things get much easier now your buddies weight is off your body.

Rescue with three or more people on the rope:

With extra people, things get much easier. More pulling power.  The downside? To quote an old English saying: “Too many cooks spoil the broth”.  More people require an element of organisation and while all members of the group might feel they are experienced and skilled in buddy rescue you might find you are the only one in practice. Couple this with the fact that laying at the end of the rope screaming is someone’s partner and suddenly a nice walk in the mountains requires a high level of technical skills and people management.

Crevasse rescue with 3 or more people on the rope. A person has fallen in. The second and third person take the load. The second person is know trying to place an ice screw to form the first belay. The guy standing straight with his back to the camera is an instructor with the safety rope.

In this scenario, we have three people on a single rope, which is not uncommon if you’re crossing a glacier on a general mountaineering trip that does not require any technical climbing during the tour.

Basic equipment per person:

2 x prusiks

1 x snow anchor ( or just an ice axe)

1 x ice screw

Team equipment:

A single rope.

The basic set up is for 3 people on the same rope; The second person in the group ties in the middle of the rope (often with a overhand knot on the bight – A fig 8 would be to big) and then the two other people tie in 8m or so from this person.  The rest of the rope is coiled up over the shoulder or stored in the rucksack. The end people have a 1x prusik on the rope, while the middle person has 2 x prusiks (one on each rope going to the buddies).

When a person falls into a crevasse the other people brace and stop the fall. Often enough if they are quick and have good rope discipline they could just drag there buddy out. If this is not possible and said buddy can’t climb out with the help of there buddies the second person makes an anchor with the ice screw or snow anchor and attaches the relevant prusik to the rope.  They transfer the weight gingerly onto the belay with the aid of the third person, once this is done and it works the third person can come forward and set up the rescue belay. If there are only 3 people its probable best to set up between the second guy and the crevasse so the second guy can help pull as well as take control of there own back-up belay.  The third guy set up the belay and attaches the end of the rope to the belay and drops a loop of rope with a friendly screw gate carabiner to the buddy in the crevasse who clips this onto the central loop on there harness. They can also put a rucksack under the rescue rope to stop it cutting into the snow at the lip of the crevasse. The other end of the loop is brought back to the rescue belay and a prussic is attached to the rope. Sometimes I have seen people attach this prussic onto a 60cm sling others have used a French prussic direct on the carabiner. Both work. Both have advantageous and disadvantageous. Now it set up. Phew. Lets get pulling. The second and third person can pull on this 2:1 system and if you buddy in the hole can help they can also pull on the right rope to aid the up and out. Once you have pulled up a bit the second person can take up the slack on the main line though there prussic as a back-up.

Crevasse rescue with 3 or more people. The second person (red jacket on the right) has place the ice screw and taken the load on a prusik. The third person (orange jacket on the left) places the second ice screw to form the rescue belay.

Discussion:

This system is very simple although it might seem complicated, and requires the minimal of equipment. It does require the people on the topside to work together and if they don’t have the technical skills to make it work be able to take instruction on how.

Normally the second person on the rope is the leader and will become the boss when things go crazy.

 

 

 

 

What crevasse rescue equipment?

By | Crevasse rescue, Mountaineering Equipment | No Comments

Best to avoid crevasses especially big ones

When going on a tour that involves a glacier crossing or for that matter any tour that covers ground that you might encounter holes in the snow it is essential you have the right kit.  One of the questions we often get on the courses we provide is what equipment for which tour.

So here we go!

Firstly I would assess the tour, tour buddies, and the type of glacier I would be crossing.  The questions I would ask is how well do I know this glacier, is it snow covered (wet) or bare (dry) as in ice, will there be snow bridges, how much snow. For example a glacier in Norway in summer might be blue ice (dry) with little or no snow bridges, however, early in the season it might be snow covered and again in Spring I might ski across it and not bother to take any rescue kit as all the crevasses are deeply buried (or buried enough).  Moving on to my buddies I ask the question how experience are they in actual buddy rescue?  I have buddies that very experience but have no idea about buddy rescue.  Once we have made the assessment we can select the gear as appropriate.

Tour 1 – Alpine tour:

This is a lightweight tour, with an equally experienced buddy who is of similar weight.  We are moving light and fast. The glacier crossing is transport to the route, we don’t expect to fall in, however, we are ready! The glacier could be snow covered or ice, or both.

Kit:

1) Mountaineering ice axe (preferable T rated)

2) 120 cm sling with screw carabiner

3) 60cm sling with 2 x open carabiners

4) 2 x prusiks on an open carabiner

5) 2 x ice screws (I prefer a 20cm and 16cm)

 

Simple basic kit which will almost certainly be a part of an alpine climbing rack.  Really the only additional pieces of kit are the ice axe and ice screws

Crevasse rescue with deadman belay. It would better if the participant was pulling in the same direction as the anchor and not at an angle. No gadgets just rope and carabiners.

My reasoning is quite simple your on a lightweight tour, you don’t want the faff of additional equipment, you’re knowledgeable about the route, what to expect and this kit is just in case everything goes crazy.   You can use the axe as the snow belay and the ice screws as the ice belay. It’s as simple as that.

Note:  This system will form a classic 3:1 pulley, it works but is hard work and there is loads of friction.  If you have tried this method then boy you’re going to have to work really hard to drag your buddy out of the crevasse. Don’t kid yourself if you’re a bit pasty in the body and your mate is a bit on the chubby side your going to need a bit more help.

You can get this help with a few additional pieces of kit:

You probably have this on your rack already:

1 x extra 120cm sling or a length of cord (probably your abseil cord)

This can be built into your 3:1 system to form a help as in a 3:2:1

It makes a big difference to the pulley.

 

 

Tour 2 – Glacier / Mountaineering tour:

This is a general mountaineering tour that crossing or a glacier.  The glacier is generally snow-covered, with varying size of crevasses.  The group has a mix of experience and more importantly interest in crevasse rescue. On this type of tour I would expect some members of the group to be able to instigate a rescue, however, some will get confused or its been so long since the last course they have forgotten.  In this situation, there are more than 3 people and therefore more pulling power! That’s going to make the job 100% easier from the very start.  We might even not need to set anything up, and if we are quick and have good rope discipline we might if the person slips through the snow, reverse the rope team and drag them out 🙂

 

 

 

Kit: As before but with additions

1) Mountaineering ice axe (preferable T rated)

2) 120 cm sling with screw carabiner

3) 60cm sling with 2 x open carabiners

4) 2 x prusiks on an open carabiner

5) 1 x ice screws (I prefer a 20cm)

6) Snow anchor (or sometimes referred to as a Deadman)

Each member in the group would have the standard kit as described in the list 1 to 5 above and in this case only 1 x ice screw and a snow belays.  If you’re an experienced group you might say we will just use our axes for the belay and drop the snow anchor. There isn’t much point carrying a snow anchor if you don’t know how to use it.

On this type of tour, I am thinking snow-covered glacier where the danger of falling through the snow is a real possibility.

Some people might use a snow picket rather than a deadman. Either way, you need to know how to place them correctly and understand their limitations.

Tour 3 – Glacier crossing with heavy lumps or inexperienced people.

On this type of tour, the group is made up of some heavy lumps and/or people that have little experience or little interest in all things ropey and knotty. They are going on tour and knots are just a bewildering spiders web of little or no interest.

If I am crossing a glacier with the above-mentioned group I will always take the extra kit to help. I might be able to get my buddies to help with the pulling but setting up will be up to me and me alone.

At top of the picture is a Petzel pulley set up made for crevasse rescue. It includes:

Micro Traxion: which has the function of being a free rolling pulley or it can be locked to form a directional pulley and rope grab.

A free running pulley to reduce friction (The biggest problem faced with any pulley system)

A tibloc: A metal device to grip the rope like your prusiks.

This system reduces the friction of a pure rope and carabiner pulley system significantly.  If I was crossing a glacier, a really nasty glacier where the chances of falling in crevasses repeatedly are real then I would certainly think about taking this kit.  If you have ever rescued your mate with a 3:1 pulley made from rope and carabiners you will understand where I am coming from.

Rescue me by Mammut. 9:1 lift / easy to hop over hindering knots

Alternatively, you can buy a fancy 9:1 pulley system which is dedicated to crevasse rescue. This system is easy to use, making light work of hauling your oversized buddy out of a hole. I have to admit I dismissed this system at first then a participant brought one on a course and I was sold.  If I was running a course, for example skiing across a glacier in spring and we had no intention of climbing after the crossing I would definitely take this kit. This kit also has the nifty ability to jump over hindering knots (often alpine butterflies), which would be challenging with other sets ups.

Booking enquiry
close slider

    Booking Enquiry

    What course(s) are you interested in?

    Avalanche courseMountaineeringAlpine skillsMountain mentoringIce climbingOther

    Do you want accommodation with us?

    YesNo